DAVIS Vantage Pro ISS Retrofit Kit Instrukcja Instalacji

Product # 6921, 6921CVANTAGE PRO® AND VANTAGE PRO PLUS™Fan-Aspirated ISS Retrofit KitInstallation Instructions Estimated Time Required: 60 MinutesThes

Page 10 Installation - ISS with Internal SIMPowering the Wireless ISS SIMWireless versions of the ISS receive most of their power from the solar panel

Installation Outline Page 11Procedure 11. Mount the ISS and SIM HousingRefer to the following illustrations and refer to this section in your ISS Inst

Page 12 Installation - ISS with Internal SIMProcedure 12. Return the Old SIM to Davis1. Please return the old SIM and SIM housing (if you have one), i

Installation Outline Page 13Installation - ISS with External SIMUse these steps to install the retrofit kit on an ISS that has the SIM mounted externa

Page 14 Installation - ISS with External SIM3. Remove the cardboard packing insert and discard.4. Remove the three (3) screws connecting the mounting

Installation Outline Page 156. Remove the top two (2) radiation shield plates to expose the fan plate and junction board.2" Screws (3)Lock Washer

Page 16 Installation - ISS with External SIMProcedure 3. Mount the new Temp/Hum module1. Remove the Fan from the lower section of the radiation shield

Installation Outline Page 17Procedure 4. Re-assemble the Radiation ShieldRefer to the disassembly drawings shown in Step 2 to re-assemble the Radiatio

Page 18 Installation - ISS with External SIMProcedure 6. Connect Sensor Cables to the New SIM.The ISS sensors are connected by cables to the Sensor In

Installation Outline Page 194. Cabled ISS: run the console cable through this second grommet.5. Install the first grommet in the left slot in the SIM

Page 2ISS With Internally Mounted SIM These are the procedures required to install the Fan-Aspirated ISS Retrofit Kit on an ISS that has the SIM mount

Page 20 Installation - ISS with External SIMProcedure 8. Decommission the Old SIM (Wireless ISS only)Even after removing the battery, the old transmit

Installation Outline Page 211/4" Flat Washers1/4" Lock Washers1/4" x 1-1/2" Lag Screws1/4" Flat Washer1/4" Lock Washer1/

Page 22 Installation - ISS with External SIMProcedure 11. Return the Old SIM to Davis1. Please return the old SIM and SIM housing (if you have one), i

Troubleshooting Page 23ISS2 SPARS RetroKit D011.fm Page 23 Wednesday, April 23, 2003 11:26 AM

Product Numbers: 6921, 6921CDavis Instruments Part Number: 7395.132Fan-Aspirated ISS Retrofit KitRev. B (April 16, 2003)This product complies with the

Installation Outline Page 3Installation - ISS with Internal SIMUse these procedures to install the retrofit kit on an ISS that has the SIM mounted ins

Page 4 Installation - ISS with Internal SIM3. Locate the SIM inside the upper section of the radiation shield.4. Disconnect the WIND sensor (anemomete

Installation Outline Page 52. The SIM transmitter board, dust cover, and rear cover plate (not shown) are attached to the top radiation shield plate u

Page 6 Installation - ISS with Internal SIM3. Install the new Temp/Hum module, being sure to set the sensor cable in the cable channel in the fan plat

Installation Outline Page 74. Install the Junction Board cover as shown above. The cover installs easily by pressing it into place. 5. Slide the two s

Page 8 Installation - ISS with Internal SIM3. Take the same colored wire from the other cable and place it into the other hole at the end of the splic

Installation Outline Page 96. Refer to the ISS SIM Connections illustration and connect only the sensor cables as shown. You will connect the power ca